ECE 210 Resonance Circuits Using Simulation
Order ID:89JHGSJE83839 Style:APA/MLA/Harvard/Chicago Pages:5-10 Instructions:
ECE 210 Resonance Circuits Using Simulation
Laboratory Procedures
DeVry University
College of Engineering and Information Sciences
- OBJECTIVES
- To simulate the operation of a series and parallel resonance circuit consisting of a resistor (R), an inductor (L), and a capacitor (C).
- To plot the resonance curves of the simulated RLC circuit by varying the AC voltage source. frequency.
- To build series and parallel RLC resonance circuit and to verify the results obtained by simulation.
- PARTS LIST
Equipment:
IBM PC or compatible
Function generator
DMM (digital multimeter)
Parts:
1 – 470 Ω resistor 1 – 1 µF capacitor
1 – 47 mH inductor
Software:
MultiSim 11
III. PROCEDURE
- Simulation of a Parallel Resonance Circuit
- Construct the RLC parallel circuit shown in Figure 1. Simulate the circuit at the frequencies shown in Table 1. Note and record the current readings obtained in the table with switch S1 closed. This represents the inductor as an ideal inductor with zero wire resistance.
The inductor self-resistance, RL = 65 Ω, has been included in the schematic after measuring the actual component. If the inductor you choose has different DC resistance, please feel free to modify the circuit.
- Plot the data obtained above in the graph sheet below. Note: frequency should be on the X-axis; the source current IS (mA) should be on Y-axis.
Figure 1: Parallel Resonance Circuit
Frequency, Hz
IS (RMS), mA
IC (RMS), mA
IL (RMS), mA
200
300
500
700
730
734
738
800
1000
1200
1400
Table 1: Parallel Resonance Simulation with Switch S1 “OFF”
Plot 1 – Parallel Resonance Data
- Answer the questions below:
a)
What happens to the source current, IS, as the frequency is changed from low to high? Describe in your own words.
Answer:
b)
Did the source current, IS, go through a minimum or maximum as the frequency is changed from low to high?
Answer:
c)
What is the source frequency at the source current, IS, minimum? What do you call the frequency at that point?
Answer:
d)
What do you notice from the values of the currents IC and IL at IS minimum?
Answer:
e)
What is the phase relationship between IC and IL at IS minimum?
Answer:
f)
What happens to the total impedance, ZP, of the parallel circuit at the current minimum? Choose the correct answer below:
Answer:
- i) OPEN Circuit ii) SHORT Circuit
g)
Why is the source current, IS, minimum at this frequency?
Answer:
- Turn the switch J1 in the simulator to the OPEN condition. Vary the source frequency between 700 Hz to 734 Hz (in steps of 2 Hz) to obtain the minimum source current, IS. Note it and also record the frequency below.
New resonant frequency with the J1 switch OPEN = Hz.
5. Answer the questions below with the J1 switch open:a)
What happened to the inductive branch of the circuit with the switch J1 OPEN?
Answer:
b)
Did the resonance frequency go UP or DOWN compared with the previous result? Circle the correct answer.
Answer:
c)
Calculate the Quality Factor, Q of the inductor at this resonance frequency.
Q = {ωres L }/ RLAnswer:
- Simulation of a Series Resonance Circuit
- Construct the RLC series resonance circuit shown in Figure 2in Multisim. Simulate the circuit at the frequencies shown in Table 2, and record the current readings obtained.
The inductor self-resistance, RL = 65 Ω, has been included in the schematic. If the inductor you choose has different DC resistance, please feel free to modify the circuit.
Figure 2: Series Resonance Circuit
Frequency, Hz
IS (RMS), mA
VC (RMS), mV
VL (RMS), mV
200
300
500
700
730
734
738
800
1000
1200
1400
Table 2: Series Resonance Simulation
- Plot the data obtained above in the graph sheet below. Note: frequency should be on the X-axis; the source current IS (mA) should be on Y-axis.
- Use the simulation results to answer the following questions:
a)
What happens to the source current, IS, as the frequency is changed from low to high? Describe in your own words.
Answer:
b)
What is the source frequency at the source current, IS, maximum? What do you call the frequency at that point?
Answer:
c)
What do you notice from the values of the voltages VC and VL at IS maximum?
Answer:
d)
What is the phase relationship between VC and VL at IS maximum?
Answer:
e)
What happens to the total impedance, ZS, of the series L and C part of the circuit at this current maximum? Choose the correct answer below:
Answer:
- i) OPEN Circuit ii) SHORT Circuit
f)
Why is the source current, IS, maximum at this frequency?
Answer:
Plot 2 – Series Resonance Data
- Construction of a Series or Parallel RLC Circuit and Measurement of Circuit Characteristics
- Construct the circuit in either Figure 3 or 4.
Important note: You do not need the switch arrangement for the parallel resonance circuit; The inductor self-resistance, which is an integral part, cannot be isolated as in the simulator analysis.
Figure 3 – Parallel Resonance Circuit
Figure 4 – Series Resonance
- Set the function generator voltage to 10 V RMS. Use the same value for frequency as used in the simulator experiment.
- Vary the source frequency as indicated in the simulation part of the lab exercise. Record the current readings. Tabulate the results below:
Frequency, Hz
IS (RMS), mA
200
300
500
700
730
734
738
800
1000
1200
1400
Table 3 – Circuit Measurement Results
- Are the simulated and calculated values the same?________ (YES or NO)
- If you answered NO, explain why you think they differ.
- TROUBLESHOOTING
Describe any problems encountered and how those problems were solved.
ECE 210 Resonance Circuits Using Simulation
RUBRIC
Excellent Quality
95-100%
Introduction 45-41 points
The background and significance of the problem and a clear statement of the research purpose is provided. The search history is mentioned.
Literature Support
91-84 points
The background and significance of the problem and a clear statement of the research purpose is provided. The search history is mentioned.
Methodology
58-53 points
Content is well-organized with headings for each slide and bulleted lists to group related material as needed. Use of font, color, graphics, effects, etc. to enhance readability and presentation content is excellent. Length requirements of 10 slides/pages or less is met.
Average Score
50-85%
40-38 points
More depth/detail for the background and significance is needed, or the research detail is not clear. No search history information is provided.
83-76 points
Review of relevant theoretical literature is evident, but there is little integration of studies into concepts related to problem. Review is partially focused and organized. Supporting and opposing research are included. Summary of information presented is included. Conclusion may not contain a biblical integration.
52-49 points
Content is somewhat organized, but no structure is apparent. The use of font, color, graphics, effects, etc. is occasionally detracting to the presentation content. Length requirements may not be met.
Poor Quality
0-45%
37-1 points
The background and/or significance are missing. No search history information is provided.
75-1 points
Review of relevant theoretical literature is evident, but there is no integration of studies into concepts related to problem. Review is partially focused and organized. Supporting and opposing research are not included in the summary of information presented. Conclusion does not contain a biblical integration.
48-1 points
There is no clear or logical organizational structure. No logical sequence is apparent. The use of font, color, graphics, effects etc. is often detracting to the presentation content. Length requirements may not be met
You Can Also Place the Order at www.collegepaper.us/orders/ordernow or www.crucialessay.com/orders/ordernow